- On a hot tub, what does FC stand for?
- On a CleverSpa, what does FC stand for?
- What’s the best way to get my hot tub out of SLP mode?
- What is the procedure for checking into a spa?
- On a hottub, what does F2 mean?
- What does F2 on my hot tub mean?
- On a hot tub, what does HL stand for?
- Why isn’t my CleverSpa heating up?
- Why is my CleverSpa always deflating?
- What does SLP signify on a hot tub?
- On the Beachcomber hot tub, what does SL stand for?
- On a hot tub, what does a flashing SL mean?
- What is the best way to maintain a hot tub?
- How do you use salt to test a hot tub?
- What is the best way to inspect a Jacuzzi tub?
- What does F4 on a hottub mean?
- On a hot tub, what does E1 mean?
- What exactly is the spa code?
- On a spa, what does F1 mean?
- On a hot tub, what does F3 mean?
- On my hot tub, what does lf stand for?
- What causes a hot tub to display an HL code?
- What does the Dr code on a hot tub mean?
- What is the best way to test a spa’s high limit sensor?
- How can I tell if the heater in my hot tub is working?
- Why isn’t my hot tub maintaining its temperature?
- Why isn’t my spa pump turning on?
- How do you locate a hole in a sluggish spa?
- Is it possible for me to leave my CleverSpa on all of the time?
- Do lazy spas lose their oomph?
- How can I wake up my Beachcomber hot tub from its slumber?
On a hot tub, what does FC stand for?
“FC” stands for ” Freeze Condition “. The control system looks for a reading of 60oF (15oC) or less in the water. If a fault is identified, the topside control will display the code “FC”, which indicates that a potential freeze condition has been detected when the spa temperature falls below 60 degrees Fahrenheit (15 degrees Celsius).
On a CleverSpa, what does FC stand for?
What Does the FC Error Code Mean? When the filtration system has worked for approximately 168 hours, the FC problem number with a small light beside it will appear, recommending you to check your filter. The pump and heating controls will be turned off. – Make sure the filter is clean and replace it if necessary (See Filter Cleaning Tips).
What’s the best way to get my hot tub out of SLP mode?
Before being enlarged, a portion of the suggested span transcript is shown. So, if you repeat the process. It. It reverts to standard mode and resumes normal operation. More information is available by clicking the More button at the bottom of this page.
What is the procedure for checking into a spa?
It may take a long is a portion of the suggested span transcribed before it is expanded. Now we’ll put a cap on it, dry it off, get in your car, and drive it to your destination. More information is available by clicking the More button at the bottom of this page.
On a hottub, what does F2 mean?
The Most Comprehensive List of Spa and Hot Tub Error Codes.
CODE | DESCRIPTION OF THE ERROR CODE |
---|---|
F1 and f2 | Blown fuse (Vita Spa); replace fuse 1 or fuse 2. |
F2 | Daily filtering for 4 hours; system message, not an error |
F4 | Daily filtering for 8 hours; system message, not an error |
F6 | Filtration for 12 hours each day; system message, not an error |
What does F2 on my hot tub mean?
The F2 error code is commonly associated with a balboa power pack system and indicates a flow issue in your hot tub.
On a hot tub, what does HL stand for?
Hi-Limit is indicated by the HL reading in the display. The hi-limit is based on the temperature of the heater rather than the spa’s actual water temperature. If your spa’s temperature reading is HL, it won’t let your heater switch on, therefore the pumps will be operating nearly 24 hours a day.
Why isn’t my CleverSpa heating up?
It’s possible that your filter is clogged. A clogged filter will prevent water from being drawn through the internal heater and heated before being pushed back into the hot tub. If you’re not sure if your filter is clean, check our video.
Why is my CleverSpa always deflating?
A fault with the valves or a hole in the liner can cause air loss in your CleverSpa®. Clever Company will not be held liable for any punctures to your CleverSpa®.
What does SLP signify on a hot tub?
The Spa is in the Sleep Heating Mode if the SLP or SL Message is ON Solid (Not Flashing) on the Display, but there is no current water temperature because the Spa is between Filter Cycles.
On the Beachcomber hot tub, what does SL stand for?
Error codes for Beachcomber.
This is the message… | That is to say… |
---|---|
2 Std/Std/Std/Std/Std STANDARD | In Standard Mode, the hot tub is operating. |
3 ECONOMY (ECN/EC) | The hot tub is in Economy Mode right now. |
4 SLEEP SLP/SL SLP/SL SLP/SL SLP/SL SLP/ | The hot tub is set to the sleep heating setting. The hot tub is turned off if the display just shows this message blinking. |
On a hot tub, what does a flashing SL mean?
So, what is the Sleep Mode of a Hot Tub? The jets in your hot tub will periodically work to filter the water while it is in sleep mode (or ‘SL & SLP mode on some models ). Your hot tub’s heater will normally only come on in sleep mode if the temperature drops below 20 degrees below the programmed temperature.
What is the best way to maintain a hot tub?
Once every three months. It is recommended that the water in your Hot Tub be changed every three months. At this point, a pipe cleaner can be used, which is inserted while the water is hot, run through pumps for about 30 minutes, and then drained. The inside of the tub’s shell will need to be cleaned with a spa-friendly cleanser, rinsed, and dried.
How do you use salt to test a hot tub?
Add 12 of the suggested amount of FreshWater Salt to the filter compartment of the hot tub while the jets are operating. Take a 30-minute break. After 30 minutes, repeat the process with another cup of salt every 15 minutes until the panel reads in the middle of the green range for salt and the Salt Test Strip reads 1,750 ppm.
What is the best way to inspect a Jacuzzi tub?
You’ll have your bottle of test strips, according to a portion of the indicated span transcript before it was increased. And you’re going to put it in the water for three minutes or such. More information is available by clicking the More button at the bottom of this page.
What does F4 on a hottub mean?
Some hot tubs use the numbers F2, f4, and F6 to indicate how long they are set to filter. F2 equals 4 hours, f4 equals 8 hours, and F6 equals 12 hours. Hold – When the panel buttons have been pressed too many times or too quickly, this message appears.
On a hot tub, what does E1 mean?
When the Portable Control Unit (PCU) detects a failure with the temperature sensors, the E1 Error Code is activated. A worn sensor, damaged connection, or faulty wiring could be the source of this problem.
What exactly is the spa code?
A single-page interface is another term for an SPA (SPI). A single-page application can either load all of the HTML, javaScript, and CSS code on the first load or dynamically load resources in response to user interaction or other events.
On a spa, what does F1 mean?
Filtration cycles range from F1 to F8, with F1 equaling 1 hour every 12 hours and F8 equaling 8 hours every 12 hours. The factory-set cycle is F1, thus if you’re in ec or sl mode, your water won’t reach the desired temperature.
On a hot tub, what does F3 mean?
Cycles of Filtering The filter program also regulates the operation of the spa heater, as follows: • Filter programs (F0, f1, f2, f3) that are standard: When the water temperature falls 2 degrees below the predetermined setting, the heater kicks on (Jets 1 low speed also activates on non-Circulation Pump models).
On my hot tub, what does lf stand for?
LF stands for persistent low flow issues. (Within 24 hours, the 5th occurrence of the “HFL” warning is displayed.) The heater is turned off, but the rest of the spa works normally. Dr = Inadequate water in the heater has been observed.
What causes a hot tub to display an HL code?
When the “HL” error notice flashes, the system has shut down because the spa’s water temperature has reached 112°F (44°C). Only Smart Winter Mode will be activated in this situation. DO NOT PUT YOUR FEET IN THE WATER. Remove the spa’s heat cover to let the water cool down.
What does the Dr code on a hot tub mean?
According to Niagara Hot Tubs, a message like “dr” or “dry” or “heater dry” indicates that there is no water in the heater tube. Although safety sensors are designed to detect a dry state and turn off the heater, before troubleshooting the equipment, make sure to manually cut power to the pump and heater.
What is the best way to test a spa’s high limit sensor?
Temperature Sensors at a Spa are being tested.
- At the breaker and spa pack, turn off all power to the spa.
- Set your Ohm meter to a reading of 20K.
- Remove the plug from the board and locate the wire ends.
- Connect the green and red wires with your meter lines.
- Use the Thermistor Resistance vs. Temperature Chart to compare your results.
How can I tell if the heater in my hot tub is working?
You can detach the copper tabs (or wires) from the spa pack to the heater element to see if a malfunctioning heater is the source of your tripped breaker. Reconnect the electricity once it has been disconnected. If the breaker stays on, you know the heater isn’t working.
Why isn’t my hot tub maintaining its temperature?
The issue could be caused by a clogged spa filter. Check the flow rate or pressure by removing the spa cartridge, cleaning the filters, and removing the spa cartridge. A damaged valve, clogged spa jets or pipes, or a broken pump impeller are all possible causes. The noticeable reduction in flow into your spa or hot tub will alert you to this.
Why isn’t my spa pump turning on?
Check that the power is on, that the breaker or GFCI test button is not tripped, and that all valves are open. Look for any kinks in the hose as you follow the circ pump plumbing. Remove the cartridge filter to observe whether the circulation pump performs better and the flow improves.
How do you locate a hole in a sluggish spa?
To do this, you’ll need more of the water-and-soap mixture you used around the air valve in the spray bottle. First, give your hot tub’s walls a clean scrub down, then inflate it until it’s nice and firm. The puncture will be visible when the soapy mixture begins to bubble.
Is it possible for me to leave my CleverSpa on all of the time?
Do not turn on the CleverSpa® if it is empty, as this may cause irreversible damage to the pump mechanism, voiding any warranty. The CleverSpa® should not be put up or left outside in temperatures below 6°C (43°F), as this may result in irreversible damage, voiding any warranty.
Do lazy spas lose their oomph?
Use the Lay-Z-Spa deflation T Joint to easily deflate your inflatable hot tub once it is empty and thoroughly dry. Connect the inflate hose to the T Joint on the AirJetTM outlet, and connect the deflation hose attachment to the other end.
How can I wake up my Beachcomber hot tub from its slumber?
To exit standby mode, press any button. When standby is selected when the hot tub is in a heat cycle, the 2 speed pump or Hush Pump will run for roughly 15 seconds. During filtration, the two-speed filter pump or Hush Pump and ozone generator will run on all systems.
Category:Spas & Beauty Services